Manjaro XFCE Edition
   1302

Черный экран после включения swap файла (файла подкачки)

Всем привет, после включения опции swap я получаю черный экран в момент загрузки системы.

Подключал swap по этому мануалу. Swap работал до перезагруки.

Я выключил опцию
quite
при загрузке, добавил
nomodeset
и вижу такую картину:

// [ OK ] banch of OK messages...
[    **] A start job is runnning for /dev/disk/by-uuid/d381f6c5-aa84-...{uuid} (1 min 2s / 1min 30s)
[ TIME ] Timed out waiting for device /dev/disk/by-uuid/d381f6c5-aa84-...{uuid}
[DEPEND] Dependency failled for /swapfile
[DEPEND] Dependency failed for Local File Systems
// [ OK ] banch of OK messages...


Насколько я понимаю, неправильно указал UUID вот здесь
/etc/fstab


Как мне поменять или закомментировать строку, которая вызывает ошибку? У меня установлена Windows 10, можно ли как-то безопасно изменить файл `/etc/fstab` через нее например? Нашел пока способ только прочитать этот файл.

Или возможно у Manjaro есть какая-то альтернатива Safe mode в Windows?

Или опять все переустанавалить?)

Данные системы, до этой ошибки:
System:
  Kernel: 5.10.56-1-MANJARO x86_64 bits: 64 compiler: gcc v: 11.1.0 
  parameters: BOOT_IMAGE=/boot/vmlinuz-5.10-x86_64 
  root=UUID=f39d9866-5be6-4713-b625-36fb4ec289a4 rw quiet apparmor=1 
  security=apparmor udev.log_priority=3 
  Desktop: Xfce 4.16.0 tk: Gtk 3.24.29 info: xfce4-panel wm: xfwm 4.16.1 vt: 7 
  dm: LightDM 1.30.0 Distro: Manjaro Linux base: Arch Linux 
Machine:
  Type: Laptop System: ASUSTeK product: N552VW v: 1.0 serial: <filter> 
  Mobo: ASUSTeK model: N552VW v: 1.0 serial: <filter> 
  UEFI: American Megatrends v: N552VW.300 date: 08/31/2016 
Battery:
  ID-1: BAT0 charge: 26.4 Wh (76.3%) condition: 34.6/48.2 Wh (71.7%) 
  volts: 14.4 min: 14.4 model: ASUSTeK ASUS Battery type: Li-ion serial: N/A 
  status: Charging cycles: 354 
Memory:
  RAM: total: 15.53 GiB used: 2.77 GiB (17.9%) 
  RAM Report: permissions: Unable to run dmidecode. Root privileges required. 
CPU:
  Info: Quad Core model: Intel Core i7-6700HQ bits: 64 type: MT MCP 
  arch: Skylake-S family: 6 model-id: 5E (94) stepping: 3 microcode: EA cache: 
  L2: 6 MiB bogomips: 41621 
  Speed: 800 MHz min/max: 800/3500 MHz Core speeds (MHz): 1: 800 2: 800 3: 802 
  4: 800 5: 800 6: 800 7: 800 8: 800 
  Flags: 3dnowprefetch abm acpi adx aes aperfmperf apic arat arch_perfmon art 
  avx avx2 bmi1 bmi2 bts clflush clflushopt cmov constant_tsc cpuid 
  cpuid_fault cx16 cx8 de ds_cpl dtes64 dtherm dts epb ept ept_ad erms est 
  f16c flexpriority flush_l1d fma fpu fsgsbase fxsr hle ht hwp hwp_act_window 
  hwp_epp hwp_notify ibpb ibrs ida intel_pt invpcid invpcid_single lahf_lm lm 
  mca mce md_clear mmx monitor movbe mpx msr mtrr nonstop_tsc nopl nx pae pat 
  pbe pcid pclmulqdq pdcm pdpe1gb pebs pge pln pni popcnt pse pse36 pti pts 
  rdrand rdseed rdtscp rep_good rtm sdbg sep smap smep ss ssbd sse sse2 sse4_1 
  sse4_2 ssse3 stibp syscall tm tm2 tpr_shadow tsc tsc_adjust 
  tsc_deadline_timer vme vmx vnmi vpid x2apic xgetbv1 xsave xsavec xsaveopt 
  xsaves xtopology xtpr 
  Vulnerabilities: Type: itlb_multihit status: KVM: VMX disabled 
  Type: l1tf 
  mitigation: PTE Inversion; VMX: conditional cache flushes, SMT vulnerable 
  Type: mds mitigation: Clear CPU buffers; SMT vulnerable 
  Type: meltdown mitigation: PTI 
  Type: spec_store_bypass 
  mitigation: Speculative Store Bypass disabled via prctl and seccomp 
  Type: spectre_v1 
  mitigation: usercopy/swapgs barriers and __user pointer sanitization 
  Type: spectre_v2 mitigation: Full generic retpoline, IBPB: conditional, 
  IBRS_FW, STIBP: conditional, RSB filling 
  Type: srbds mitigation: Microcode 
  Type: tsx_async_abort mitigation: Clear CPU buffers; SMT vulnerable 
Graphics:
  Device-1: Intel HD Graphics 530 vendor: ASUSTeK driver: i915 v: kernel 
  bus-ID: 00:02.0 chip-ID: 8086:191b class-ID: 0300 
  Device-2: NVIDIA GM107M [GeForce GTX 960M] vendor: ASUSTeK driver: nvidia 
  v: 470.57.02 alternate: nouveau,nvidia_drm bus-ID: 01:00.0 
  chip-ID: 10de:139b class-ID: 0302 
  Device-3: IMC Networks USB2.0 HD UVC WebCam type: USB driver: uvcvideo 
  bus-ID: 1-4:3 chip-ID: 13d3:5666 class-ID: 0e02 serial: <filter> 
  Display: x11 server: X.Org 1.20.13 compositor: xfwm4 v: 4.16.1 driver: 
  loaded: modesetting,nvidia unloaded: intel,nouveau alternate: fbdev,nv,vesa 
  display-ID: :0.0 screens: 1 
  Screen-1: 0 s-res: 3840x2160 s-dpi: 96 s-size: 1016x571mm (40.0x22.5") 
  s-diag: 1165mm (45.9") 
  Monitor-1: eDP-1 res: 3840x2160 hz: 60 dpi: 284 size: 344x194mm (13.5x7.6") 
  diag: 395mm (15.5") 
  OpenGL: renderer: Mesa Intel HD Graphics 530 (SKL GT2) v: 4.6 Mesa 21.1.6 
  direct render: Yes 
Audio:
  Device-1: Intel 100 Series/C230 Series Family HD Audio vendor: ASUSTeK 
  driver: snd_hda_intel v: kernel bus-ID: 00:1f.3 chip-ID: 8086:a170 
  class-ID: 0403 
  Device-2: Sennheiser Headset [PC 8] type: USB 
  driver: hid-generic,snd-usb-audio,usbhid bus-ID: 1-6:4 chip-ID: 1395:0025 
  class-ID: 0300 
  Sound Server-1: ALSA v: k5.10.56-1-MANJARO running: yes 
  Sound Server-2: JACK v: 1.9.19 running: no 
  Sound Server-3: PulseAudio v: 15.0 running: yes 
  Sound Server-4: PipeWire v: 0.3.33 running: no 
Network:
  Device-1: Intel Wireless 7265 driver: iwlwifi v: kernel port: e000 
  bus-ID: 02:00.0 chip-ID: 8086:095a class-ID: 0280 
  IF: wlp2s0 state: up mac: <filter> 
  IP v4: <filter> type: dynamic noprefixroute scope: global 
  broadcast: <filter> 
  IP v6: <filter> type: noprefixroute scope: link 
  Device-2: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet 
  vendor: ASUSTeK driver: r8169 v: kernel port: d000 bus-ID: 03:00.1 
  chip-ID: 10ec:8168 class-ID: 0200 
  IF: enp3s0f1 state: down mac: <filter> 
  WAN IP: <filter> 
Bluetooth:
  Device-1: Intel Bluetooth wireless interface type: USB driver: btusb v: 0.8 
  bus-ID: 1-9:5 chip-ID: 8087:0a2a class-ID: e001 
  Report: rfkill ID: hci0 rfk-id: 1 state: down bt-service: enabled,running 
  rfk-block: hardware: no software: yes address: see --recommends 
Logical:
  Message: No logical block device data found. 
RAID:
  Message: No RAID data found. 
Drives:
  Local Storage: total: 2.29 TiB used: 71.69 GiB (3.1%) 
  SMART Message: Required tool smartctl not installed. Check --recommends 
  ID-1: /dev/sda maj-min: 8:0 vendor: SK Hynix model: HFS512G39MND-3510A 
  size: 476.94 GiB block-size: physical: 4096 B logical: 512 B speed: 6.0 Gb/s 
  type: SSD serial: <filter> rev: 0P00 scheme: GPT 
  ID-2: /dev/sdb maj-min: 8:16 vendor: Seagate model: ST2000LM003 HN-M201RAD 
  size: 1.82 TiB block-size: physical: 4096 B logical: 512 B speed: 6.0 Gb/s 
  type: HDD rpm: 5400 serial: <filter> rev: 0001 scheme: GPT 
  Optical-1: /dev/sr0 vendor: HL-DT-ST model: DVDRAM GUE1N rev: AS00 
  dev-links: cdrom 
  Features: speed: 24 multisession: yes audio: yes dvd: yes 
  rw: cd-r,cd-rw,dvd-r,dvd-ram state: running 
Partition:
  ID-1: / raw-size: 98.81 GiB size: 96.7 GiB (97.86%) used: 71.66 GiB (74.1%) 
  fs: ext4 dev: /dev/sda5 maj-min: 8:5 label: N/A 
  uuid: f39d9866-5be6-4713-b625-36fb4ec289a4 
  ID-2: /boot/efi raw-size: 100 MiB size: 96 MiB (96.00%) 
  used: 25.3 MiB (26.3%) fs: vfat dev: /dev/sda2 maj-min: 8:2 label: N/A 
  uuid: 7E48-4C5B 
Swap:
  Alert: No swap data was found. 
Unmounted:
  ID-1: /dev/sda1 maj-min: 8:1 size: 499 MiB fs: ntfs 
  label: \xd0\x92\xd0\xbe\xd1\x81\xd1\x81\xd1\x82\xd0\xb0\xd0\xbd\xd0\xbe\xd0\xb2\xd0\xb8\xd1\x82\xd1\x8c 
  uuid: CCBA479BBA478146 
  ID-2: /dev/sda3 maj-min: 8:3 size: 16 MiB fs: <superuser required> 
  label: N/A uuid: N/A 
  ID-3: /dev/sda4 maj-min: 8:4 size: 377.53 GiB fs: ntfs label: N/A 
  uuid: 0434816F34816490 
  ID-4: /dev/sdb1 maj-min: 8:17 size: 16 MiB fs: <superuser required> 
  label: N/A uuid: N/A 
  ID-5: /dev/sdb2 maj-min: 8:18 size: 878.89 GiB fs: ntfs label: N/A 
  uuid: 447C577C7C5767A6 
  ID-6: /dev/sdb3 maj-min: 8:19 size: 984.11 GiB fs: ntfs label: N/A 
  uuid: 1024636424634BB2 
USB:
  Hub-1: 1-0:1 info: Full speed (or root) Hub ports: 16 rev: 2.0 
  speed: 480 Mb/s chip-ID: 1d6b:0002 class-ID: 0900 
  Device-1: 1-1:2 info: A4Tech XL-730K / XL-750BK / XL-755BK Mice 
  type: Keyboard,Mouse driver: hid-generic,usbhid interfaces: 2 rev: 1.1 
  speed: 12 Mb/s power: 100mA chip-ID: 09da:9090 class-ID: 0301 
  Device-2: 1-4:3 info: IMC Networks USB2.0 HD UVC WebCam type: Video 
  driver: uvcvideo interfaces: 2 rev: 2.0 speed: 480 Mb/s power: 500mA 
  chip-ID: 13d3:5666 class-ID: 0e02 serial: <filter> 
  Device-3: 1-6:4 info: Sennheiser Headset [PC 8] type: Audio,HID 
  driver: hid-generic,snd-usb-audio,usbhid interfaces: 4 rev: 1.1 
  speed: 12 Mb/s power: 100mA chip-ID: 1395:0025 class-ID: 0300 
  Device-4: 1-9:5 info: Intel Bluetooth wireless interface type: Bluetooth 
  driver: btusb interfaces: 2 rev: 2.0 speed: 12 Mb/s power: 100mA 
  chip-ID: 8087:0a2a class-ID: e001 
  Device-5: 1-12:6 info: Atmel type: HID 
  driver: hid-generic,hid-multitouch,usbhid interfaces: 2 rev: 2.0 
  speed: 12 Mb/s power: 100mA chip-ID: 03eb:8a9c class-ID: 0300 
  Hub-2: 2-0:1 info: Full speed (or root) Hub ports: 8 rev: 3.0 speed: 5 Gb/s 
  chip-ID: 1d6b:0003 class-ID: 0900 
  Hub-3: 3-0:1 info: Full speed (or root) Hub ports: 2 rev: 2.0 
  speed: 480 Mb/s chip-ID: 1d6b:0002 class-ID: 0900 
  Hub-4: 4-0:1 info: Full speed (or root) Hub ports: 2 rev: 3.1 speed: 10 Gb/s 
  chip-ID: 1d6b:0003 class-ID: 0900 
Sensors:
  System Temperatures: cpu: 51.0 C mobo: N/A 
  Fan Speeds (RPM): cpu: 2000 
Info:
  Processes: 259 Uptime: 5m wakeups: 91 Init: systemd v: 248 tool: systemctl 
  Compilers: gcc: 11.1.0 alt: 10 clang: 12.0.1 Packages: 1311 pacman: 1307 
  lib: 345 flatpak: 0 snap: 4 Shell: Zsh v: 5.8 running-in: xfce4-terminal 
  inxi: 3.3.06 

1 комментарий

avatar
Или возможно у Manjaro есть какая-то альтернатива Safe mode в Windows?
У манджары есть
  1. Загрузчик может передать параметры systemd.unit=emergency.target или systemd.unit=rescue.target.
  2. Лайвсд. При желании с чрутом.
0
Только зарегистрированные и авторизованные пользователи могут оставлять комментарии.